Webike STOCK RECOMMENDATIONS - FAST SHIP
廠商在庫
廠商在庫
KITACO
New Super Oil Cooler KIT
廠商在庫
KITACO
Super Oil Cooler Kit
廠商在庫
KITACO
Oil Cooler Condenser
廠商在庫
SP武川
Compact Cool Kit
廠商在庫
廠商在庫
OPMID
OPM PnP Thermometer
廠商在庫
廠商在庫
OPMID
OPM PnPThermometer
廠商在庫
廠商在庫
SP武川
Oil Line Hose Kit
![【SP武川】[Repair Parts] Oil Cooler Unit](https://webike-cdn-net.azureedge.net/catalogue/images/115251/07-07-0268_01_s.jpg)
廠商在庫
FITMENT
[要點]
★商品規格
適用車型：
適用於配備 SP 武川 e-stage / S stage / Super head 4V + R 加大缸徑套件 181cc（大型節流閥）的車輛
油管規格：
不鏽鋼編織油管 #4
商品安裝說明書＞＞點此連結
[商品描述]
此機油冷卻器套件適用於改裝SP Takegawa 的 e-Stage 加大缸徑套件和加大節流閥、S-Stage 加大缸徑套件或 Super Head 4V+R 加大缸徑 181cc 的套件。
需要拆下原廠空氣濾盒，於車架下方安裝SP 武川的護罩支架以固定機油冷卻器。
機油冷卻器安裝在護罩內，可以在不破壞外觀的情況下安裝。
機油冷卻器個規格可以選擇：三鰭片＆四油路 或 四鰭片＆五油路。
■關於編織軟管#4
外徑Φ11mm的尼龍編織軟管適用於小型摩托車。 內徑為Φ5.6mm，以減少機油泵的負荷。
尼龍編織軟管重量輕且靈活，在安裝時具有更大的靈活性。
■關於緊湊型機油冷卻器
冷卻效果較佳；透過安裝機油冷卻器，可以控制因汽缸加大而導致的溫度升高。
機油冷卻器需要與原廠油箱護板搭配安裝。
[注意]
※本商品適用於配備 SP 武川e-stage / S stage / Super head 4V + R 加大缸徑套件 181cc（大型節流閥）的車輛。
※SP 武川的e-stage 汽缸有機油道設計，因此無法安裝於沒有機油道的商品上。購買時請務必檢查汽缸有無機油道設計。
※本商品無法與原廠空濾盒一起使用。
※三鰭片機油冷卻器需要添加約40 cc的機油、四鰭片機油冷卻器則是約60 cc的機油。
※由於需要拆下原廠空氣濾盒，因此必須安裝SP 武川的加大節流閥套件；且將機油冷卻器固定於油箱護罩支架上。 由於油冷卻器需要一個出油口，所以需要安裝一個設計有機油道的加大缸徑汽缸。
※如果您的愛車已經是有機油道設計的加大汽缸套件安裝的車輛；但尚未改裝節流閥（原廠節流閥），您可以購買SP 武川的空濾套件來搭配此商品。
※商品尚未確認是否對應其他車種。
※陽極發色會隨使用時間而有顏色變化，請務必了解。
【要點】
■For vehicles equipped with SP Takegawa's e-Stage/S-Stage/Super Head 4V+R Big Bore Kit 181cc (Big Throttle Body Spec)
Blade Hose #4
Blade Hose #4
【商品描述】
■For vehicles equipped with SP Takegawa's e-Stage/S-Stage/Super Head 4V+R Big Bore Kit 181cc (Big Throttle Body Spec)
Blade Hose #4
Blade Hose #4
【注意】
*This product is for vehicles equipped with SP Takegawa's e-Stage Big Bore Kit / S-Stage Big Bore Kit / Super Head 4V+R Big Bore Kit 181cc with Big Throttle Body.
*SP Takegawa's e-Stage has a cylinder without an oil outlet boss.This product cannot be installed on the e stage which has a cylinder without an oil outlet boss.Please be sure to check the cylinder you are using before purchasing.
*It cannot be installed with stock air cleaner box at the same time.
*The amount of oil is usually 3 fin. to the specified amount of oil: Approx. 40cc / 4 fin: Add approx. 60cc.
*Because the stock air cleaner box needs to be removed, SP Takegawa's Big Throttle Body needs to be installed.By removing the stock cleaner box, the shrouds and air filter will be removed, so you will need to install SP Takegawa's air filter kit (for big throttle bodies) which comes with shroud brackets.Fix the oil cooler body to the shroud bracket.In addition, it is necessary to install the big bore cylinder with the oil outlet boss because the oil outlet to the oil cooler is necessary.Therefore, it cannot be installed on the e stage big bore kit which does not have the oil outlet boss.
*When this product is installed on a vehicle with a stock throttle body specification and a big bore cylinder with an oil outlet boss, this product can be installed by purchasing SP Takegawa's air filter kit for stock throttle bodies separately.In this case, you need to set the injection controller.
*Depending on the lot, the product may be delivered with the old price and label with the old JAN code before the price change.
*SP Takegawa's e-Stage has a cylinder without an oil outlet boss.This product cannot be installed on the e stage which has a cylinder without an oil outlet boss.Please be sure to check the cylinder you are using before purchasing.
*It cannot be installed with stock air cleaner box at the same time.
*The amount of oil is usually 3 fin. to the specified amount of oil: Approx. 40cc / 4 fin: Add approx. 60cc.
*Because the stock air cleaner box needs to be removed, SP Takegawa's Big Throttle Body needs to be installed.By removing the stock cleaner box, the shrouds and air filter will be removed, so you will need to install SP Takegawa's air filter kit (for big throttle bodies) which comes with shroud brackets.Fix the oil cooler body to the shroud bracket.In addition, it is necessary to install the big bore cylinder with the oil outlet boss because the oil outlet to the oil cooler is necessary.Therefore, it cannot be installed on the e stage big bore kit which does not have the oil outlet boss.
*When this product is installed on a vehicle with a stock throttle body specification and a big bore cylinder with an oil outlet boss, this product can be installed by purchasing SP Takegawa's air filter kit for stock throttle bodies separately.In this case, you need to set the injection controller.
*Depending on the lot, the product may be delivered with the old price and label with the old JAN code before the price change.
QA（0）
REVIEWS FOR THIS PRODUCT（0）
0/5