PAGE TOP

Mount Kit Multi Bar Holder

List price: TWD 585

Selling price: TWD 360 38%OFF

Get 4 Webike point (Around NT$ 4 )
*Can be used as a discount on your next purchase.

Pre-sale Service

TWD 360.000000

4 Webike point

Once you select the option, estimate delivery time will be displayed.

QTY:
Webike STOCK RECOMMENDATIONS - FAST SHIP
【DAYTONA】Multi Bar Holder Mirror Clamp Type Ship now
【DAYTONA】Mount Kit Multi Bar Holder 廠商在庫
【DAYTONA】Multi Mount Bar SC 廠商在庫
DAYTONA

Multi Mount Bar SC

$1,544(62%)

【KIJIMA】Handlebar Mount Bracket 廠商在庫
KIJIMA

Handlebar Mount Bracket

$1,107(62%)

【ENDURANCE】Universal Mirror Post Multi Bar 廠商在庫
ENDURANCE

Universal Mirror Post Multi Bar

$1,191(62%)

【KIJIMA】Handlebar Mount Bracket 廠商在庫
KIJIMA

Handlebar Mount Bracket

$1,300(62%)

【KIJIMA】Mount Bar Bracket 廠商在庫
KIJIMA

Mount Bar Bracket

$1,324(62%)

【KIJIMA】Mount Bar Bracket 廠商在庫
KIJIMA

Mount Bar Bracket

$1,252(62%)

FITMENT

[要點]

閥桿孔直徑:三角台直徑Φ17-20用

請點選此連結選購把手固定座安全帽鎖

[商品描述]

可以與另外販售的的多連桿支架一起安裝。

 

DAYTONA 把手固定座型安全帽鎖>>點此連結

 

[注意]

※ 適用車型是 DAYTON 公司所確認的車輛,但請務必測量實際車輛的孔徑。

※ Φ14-Φ15 在DAYTONA公司確認時,由於沒有對應的車型,因此沒有設定。

【※ 以下車輛不可用】

.沒有上三角台孔的車輛

.三角台孔徑不符的車輛

.有把手冠座的車輛

.有障礙物在三角台孔附近,當把手轉動時,將會堵住孔

※ CBR650R的三角台孔徑為 Φ19,不過因為把手冠座及上三角台的不規則性較大,因此無法安裝,需要另外準備5mm的墊片(Daytona公司沒有販售),若把手冠座朝向儀表端是可以安裝的,朝向騎士端無法安裝,因為會接觸到鑰匙開關處。

【要點】

Stem hole diameter: For Φ17-20

【商品描述】

Stem hole diameter: For Φ17-20

【注意】

*Compatible models are confirmed by DAYTONJA, but are for reference only.Be sure to measure the hole diameter of the actual vehicle.
*Φ14-Φ15 is not available because there was no applicable model when we checked with DAYTONA.
[*This service is not available for the following vehicles*]
・No stem holes.
・The hole diameter of the stem hole does not match.
・Vehicles with handle post.
・There is an obstacle near the stem hole, and when you turn the handlebar, the hole is blocked.

*The CBR650R has a stem holeΦ19, but the top bridge is too uneven to be installed because the bar holder and the top bridge touch each other.Use 5mm spacers (not available from DAYTONA) and bar holders can be installed on the meter side.The front side is not suitable because it contacts the cover of the key cylinder.

REVIEWS FOR THIS PRODUCT(0)

0/5