Grip Winding Replacement Type Grip Heater GH10 Built-in switch on clutch side Grip length 130mm

[Color] Electric rubber grip: Black
[Type] Standard Handle Size: For Φ22.2mm
[Power consumption] 13.5V 7.4W (LV1) -34.8W (LV5)

[Size]
・Grip Length: 130mm
・Grip inner dimensions: 127mm
・Maximum grip diameter: 32mm

[Set components]
・Grip heater body
・Throttle adapter
・Parts for mounting
・Instruction Manual

[Color] Electric rubber grip: Black
[Type] Standard Handle Size: For Φ22.2mm
[Power consumption] 13.5V 7.4W (LV1) -34.8W (LV5)

[Size]
・Grip Length: 130mm
・Grip inner dimensions: 127mm
・Maximum grip diameter: 32mm

[Set components]
・Grip heater body
・Throttle adapter
・Parts for mounting
・Instruction Manual

※The vehicle model may have different specifications in different regions and may not be compatible for installation.

*If you install this product on a motorcycle with low power generation, it will be difficult to warm up and the battery will be drained.
*In some injection vehicles, the power is controlled by a computer, and if there is an overcurrent in the power supply, the power is cut.Choose the wire without limit of power.
*Please be careful to connect to vehicles with LED taillamps and vehicles with anti-theft function such as immobilizer.
*Do not connect to thin wires such as LED lamps.This may cause abnormal overheating of the wiring.
*Please pay attention to the wiring around the key cylinder especially when the vehicle is equipped with immobilizer.This may cause the immobilizer to malfunction or the computer to fail.
*This product is a consumable item. Please replace the heat sheet when the surface of the heat sheet is scratched, cracked or worn.
*Before installing, turn on the power of the grip heater to heat the grip heater, which makes it easy to install it because it will expand in volume.
*There is a case that this product, which is a universal product, is difficult to fit or is loose depending on the handlebar used.In this case, it is necessary to modify the handlebars according to each vehicle body (shaving the mounting surface to allow the grip to fit, or increasing the bulk of the handlebar to eliminate looseness between the handlebar and the grip).
*Some models with 2-stroke engine use a single throttle pull on the accelerator pedal and will require modification for installation.
*Please do not activate the grip heater immediately after the engine is started, but after 5-10 minutes of warm-up operation.
*Voltage consumption: 7.4W (Level 1) at 13.5V voltage -34.8W (Level 5)
*Some motorcycles are designed to automatically supply electricity to other electrical systems when the accelerator is opened.In that case, the voltage may drop and the grip heater may stop operating.
*Spacers may be required when using with stock bar ends.
*This is a universal product. The compatible models listed in the compatibility information are the models and years that use the full-length grip size and the stock throttle pull-back 2-point wire system. Please check the inside of your vehicle's switch box, the total length of the stock grip, and the handlebar size beforehand.It is not guaranteed that this product will fit all applications.
*This product is not compatible with vehicles that use electronic throttle or throttle-by-wire mechanism.
*This product requires removal of the switch box and installation of the grip part, as well as processing of the power supply wiring from a place where reliable voltage can be secured. If you are unsure about this, it is recommended that you ask your nearest authorized dealer, vehicle dealer, or mechanic to do the work.
*The dimensions of the switch box and the accelerator input depending on the throttle opening are different depending on the model. Since this product is a universal product, it may be necessary to shave or cut the winding part for installation.It is strongly recommended that you consult an authorized dealer, vehicle dealer or mechanic who is familiar with the design of the motorcycle.
*This product is designed to be compatible with a wide range of bike models when used in combination with the factory bar ends, but there may be some bikes in which it cannot be used with the factory bar ends.In such cases, additional processes may be required, such as replacing the handle width with a handle width that corresponds to the legally mandated bike width.
*Regardless of whether the bike is small, large, vintage or new, there may be cases where the heat generation is delayed due to insufficient power supply or insufficient power generation, the system can be started only when riding on a highway at full throttle, or the use of the system limits the use of other electrical components.If you are concerned that the model, driving conditions and your own specifications cannot be guaranteed 100%, please consult with your dealer before purchasing the product.
*Images may contain other products.
*There may be changes in product specifications due to the manufacturer's reasons.