FITMENT
[要點]
[商品描述]
VANS × CULT MOTORCYCLE聯名握把套隆重登場。
結合VANS經典紋路提供優秀的舒適性以及減震效果。
長度125mm。
左右一組發售。
[注意]
※圖片僅供參考。
※示意圖中可能包含其他顏色。
※本產品為通用型式，購買前請確認規格是否相容。
※本產品之產地為美國，具有與日本產品截然不同的風格與設計理念，邀您一同品味。
※本產品整體長度較短，您可以參考示意圖中安裝於Kawasaki ZRX1200DAEG的效果，亦可選購間隔墊片（Kijima料號：201-5971、201-5972、201-597）。
※本產品為封閉式尾端，若要安裝平衡端子需自行加工鑽孔。
※示意圖可能存在色差，不同批次生產之產品亦可能存在些許差異。
※本產品不包含油門座。
※本產品為一組兩入，內徑較大者用於油門側。
※本商品規格可能因為製造商因素而有所變更。
【注意】
*Image may contain other colors.
*Because this product is designed to be highly versatile and is a collaborative product, it may have a long or short grip depending on the vehicle even if it is listed as a compatible vehicle as reference information.Please measure the size of the grip of your vehicle by yourself before considering.
*If the grip is too short, please consider using KIJIMA product #201-597 Grip Spacer Sponge Type Thickness 5mm, KIJIMA part #201-5971 Grip Spacer Rubber Type Thickness 3mm and KIJIMA part #201-5972 Grip Spacer Rubber Type Thickness 5mm.As you can see in the photo of Kawasaki ZRX1200DAEG, it is a short product.Please be sure to measure the grip dimensions of your vehicle before considering.
*This product is finished with a closed end. If you want to install it on a vehicle equipped with a bar end, you will need to make a hole in the grip or remove the bar end.
*Please compare the pictures with the example of KAWASAKI ZRX1200 DAEG, and recognize that the product image is only for reference and then the color may be lighter, darker, brighter or darker than you imagine due to the colorant and emulsifier used in each lot.
*Please note that product prices are subject to change without notice in light of exchange rates and world conditions.
*It is intended to slide like any other standard rubber grip.
*In order for the grips to work on a motorcycle, the stock throttle cone must be pre-installed.
*The throttle cone is not pre-installed on this grip.
*Each set comes with two grips, a grip with a samll inner diameter that slides on the clutch side and a grip with large inner diameter that slides on the throttle side.
*There may be changes in product specifications due to the manufacturer's reasons.
*Because this product is designed to be highly versatile and is a collaborative product, it may have a long or short grip depending on the vehicle even if it is listed as a compatible vehicle as reference information.Please measure the size of the grip of your vehicle by yourself before considering.
*If the grip is too short, please consider using KIJIMA product #201-597 Grip Spacer Sponge Type Thickness 5mm, KIJIMA part #201-5971 Grip Spacer Rubber Type Thickness 3mm and KIJIMA part #201-5972 Grip Spacer Rubber Type Thickness 5mm.As you can see in the photo of Kawasaki ZRX1200DAEG, it is a short product.Please be sure to measure the grip dimensions of your vehicle before considering.
*This product is finished with a closed end. If you want to install it on a vehicle equipped with a bar end, you will need to make a hole in the grip or remove the bar end.
*Please compare the pictures with the example of KAWASAKI ZRX1200 DAEG, and recognize that the product image is only for reference and then the color may be lighter, darker, brighter or darker than you imagine due to the colorant and emulsifier used in each lot.
*Please note that product prices are subject to change without notice in light of exchange rates and world conditions.
*It is intended to slide like any other standard rubber grip.
*In order for the grips to work on a motorcycle, the stock throttle cone must be pre-installed.
*The throttle cone is not pre-installed on this grip.
*Each set comes with two grips, a grip with a samll inner diameter that slides on the clutch side and a grip with large inner diameter that slides on the throttle side.
*There may be changes in product specifications due to the manufacturer's reasons.
QA（0）
REVIEWS FOR THIS PRODUCT（0）
0/5