PAGE TOP

Front Reach Seat REBEL250 REBEL250S REBEL500 MC49 PC60

List price: TWD 10,889

Selling price: TWD 9,878 9%OFF

Get 99 Webike point (Around NT$ 99 )
*Can be used as a discount on your next purchase.

Pre-sale Service

TWD 9878.000000

99 Webike point

Once you select the option, estimate delivery time will be displayed.

QTY:

FITMENT

[要點]

Height: 160-168cm (This is a hypothetical guide for operational safety.)
Compare to stock (seating position) - Upper body shifted forward about 10mm from stock
Seat surface increased approx. 30mm compared to stock by adding padding
Black Finish
Seat x 1
Tool bag x 1 (no stock tools included)
Tool bag retaining band x 1
User's Manual x 1

[商品描述]

Height: 160-168cm (This is a hypothetical guide for operational safety.)
Compare to stock (seating position) - Upper body shifted forward about 10mm from stock
Seat surface increased approx. 30mm compared to stock by adding padding
Black Finish
Seat x 1
Tool bag x 1 (no stock tools included)
Tool bag retaining band x 1
User's Manual x 1

[注意]

*We recommend the enjoyment of changing the appearance by dressing up or replacing the seat itself, so if you do not transplant the stock parts listed below from the stock seat (or if you want both the stock seat and this product seat to be in a state where they can be replaced or installed immediately), you will need the stock parts listed below separately. Please prepare them and refer to the attached instruction manual for installation on the underside of this product seat.
・Rubber (Honda stock part number 77205-MFE-670) x 2 pcs
・Sponge (Honda stock part number 77101-K87-A30) x 2 pcs
・Rubber (Honda stock part number 77205-KPP-T00) x 2 pcs
・One point stop rubber (Honda stock part number 77206-KPK-900) x 2 pcs
・2 grommets (Honda stock part number 61304-415-000)

*If you are skilled in transplanting stock parts from the underside of the seat and do not plan to use the stock seat immediately (in case you do not mind re-transplanting stock parts when using the stock seat), and furthermore, if each stock part is not deteriorated, this product is based on the stock Rebel seat from 2020 model or later. Therefore, the stock parts to be prepared separately vary depending on the model year.
・2017-2019 models: Rubber (Honda stock part number 77205-MFE-670) x 2 pcs
・Sponge (Honda stock part number 77101-K87-A30) x 2 pcs
・Rubber (Honda stock part number 77205-KPP-T00) x 2 pcs

*2020 model: Prepare 2 sponges (Honda stock part number 77101-K87-A30).

*When using the stock tool hex allen key inside the side cover on the right side of the motorcycle body to remove the stock seat, please note that the special Phillips screw that secures the hex allen key is very hard. Therefore, it is advisable to prepare a separate hex allen key in advance.
To remove the stock seat with a hexagonal Allen key, loosen the two bolts that are slightly visible at the rear of the seat while pushing the stock seat by hand.
In this case, the hexagonal Allen key may touch the pipe frame near the seat, so please apply Kijima protection film (Kijima part number 208-0852) or the like separately to prevent scratches, or carefully remove it using a towel or the like to prevent it from being scratched.
*Please note that due to the addition of extra padding, the position of the buttocks is shifted towards the front of the bike compared to the standard seat, bringing the crotch area closer to the fuel tank.
*There may be a slight gap between the seat and the frame due to individual differences in the product and production lots.
*Although waterproof measures are taken, water can easily enter through the seams due to the structure of the garment, so please maintain the garment by regularly applying waterproofing spray.
*The image may contain other products.
*There may be changes in product specifications due to the manufacturer's reasons.

REVIEWS FOR THIS PRODUCT(0)

0/5