Aluminum Ring Front Fork Slider for NC700 S / X and other models

．Applicable models: HONDA CTX700 / N (13-15), INTEGRA (NC700D) (13-15), INTEGRA (NC750D) (13-15), NC700 S / X (12-15), NC750 S / X (14-15)

Product Part Number: DI-FASR-HO-02
Product Name: Aluminum Ring Front Fork Sliders
If a heavy motorcycle unfortunately tips over, it often requires huge repair costs, especially at high speeds. If an accident occurs, excessive friction between the motorcycle body and the ground will cause the vehicle to bounce off the ground, leading to flipping and greater damage, which is often referred to on the track as (LOW-SIDE to HIGH-SIDE, where a normal sliding accident turns into a vehicle bouncing and rolling situation). The outer layer of the DIMOTIV front fork slider uses plastic steel (scientific name: polyoxymethylene, POM for short) as the main material, which has the following characteristics:
1. Shock absorption: Absorbs impact force during a tip-over, effectively protecting the motorcycle body.
2. High rigidity: Strong hardness and high wear resistance.
3. Low friction coefficient: A low friction coefficient can effectively reduce the probability of the motorcycle body bouncing and flipping due to excessive friction.

This product uses chrome-molybdenum steel to replace the original front wheel axle, which does not affect the operation of the original swingarm and wheel rim. When the slider is impacted, the impact force is transmitted to the other end through the chrome-molybdenum steel shaft to reduce the damage of the impact force directly to the swingarm and wheel rim. When the motorcycle tips over, the POM plastic block will rotate, thereby achieving the effect of reducing friction.

Product colors:
Black/Gold/Titanium

Product material:
6061-T6 aluminum-magnesium alloy: Silicon content 0.4%~0.8%; Copper content 0.15%~0.4%; Magnesium content 0.8%~1.2%; Chromium content 0.04%~0.35%. Tensile strength 42,000 psi (290 MPa), yield strength 35,000 psi (241 MPa). For plate thickness less than 0.25 inches (6.4 mm), elongation is 8% or more. For thickness greater than 0.25 inches (6.4 mm), elongation is 10%.

Chrome-molybdenum steel: A reinforced steel material with high hardness and high elastic modulus (Young's modulus 200-207). High elastic modulus means that the material has good characteristics for absorbing impact force.

Surface treatment method:
General anodizing: Anodizing with the same specifications as iPhones and tablets, featuring corrosion resistance and UV resistance, with weather resistance up to 60 hours. (Fading begins only after 60 hours of continuous exposure to UV intensity of 100eV; natural sunlight UV intensity is about 3~10eV). Dacromet anti-rust treatment: The fixing screws use premium anti-rust treatment - Dacromet, which is an anti-corrosion coating with zinc powder, aluminum powder, chromic acid, and deionized water as the main components.

Dacromet is widely used, and top-tier European motorcycle models all use this anti-rust treatment technology.

Installation instructions:
1. Please first confirm the left and right direction of the product according to the 3D diagram on the back of the product card.
2. Use a lift to raise the motorcycle frame.
3. Remove the original front wheel axle nut.
4. Remove the original wheel axle.
5. Insert the chrome-molybdenum steel shaft included with this product.
6. Then lock the sliders on both sides to complete the installation.

Note:
If the POM plastic or components are damaged and unusable, they can be purchased separately, so there is no need to spend money to buy the whole set again.

Applicable models:
HONDA
CTX700/700N 13-15
INTEGRA(NC700D) 13-15
INTEGRA(NC750D) 13-15
NC700S/700X 12-15
NC750S/750X 14-15

※The vehicle model may have different specifications in different regions and may not be compatible for installation.

【Notes before ordering】
Before ordering, please double-check the color, size, and other information you wish to purchase.
Most products have lead times provided after the order is placed, so there may be situations where products are discontinued or require a long waiting period for shipment.
If an order cannot be fulfilled due to manufacturer stock shortages or temporary unavailability, the order will not be processed; no charges will be incurred if the order is not processed.
Please note that manufacturers may unilaterally change specifications or exterior designs, which may result in packaging or product appearance differing from the images on the product page.
If a manufacturer's unilateral change in design or specifications prevents the product from performing its intended function as expected at the time of order, please contact our customer service for further assistance.
Products undergo multiple shipping processes from order to delivery, so packaging may be deformed or damaged during transit, provided the product itself remains intact and functional.
【Return Policy】
If you require a return service, please apply in the returns section; please keep the product appearance intact and sealed in its original packaging.
Upon receiving your return request, we will dispatch a logistics provider to collect the item as soon as possible.
For non-human-induced defects, please apply for a return within 7 days of receiving the product.
【Authenticity Guarantee】
For products with an authenticity guarantee, if they are found to be suspected counterfeits and confirmed by a court judgment following relevant litigation, we will compensate the customer 10 times the original purchase price.