[要點]
【尺寸】長80mmx寬140mm
【調整器機構】10段(間隔18度)
【規格】符合日本新安全標準的後視鏡
【套件內容】
・本體(2個一組)
・10mm正牙螺絲x 2 ・逆牙螺絲x 1
・8mm正牙螺絲x 2 ・逆牙螺絲x 1
【安裝時間】0.2h
[商品描述]
與眾不同的創新設計後照鏡!
使用撞擊緩衝機構! 符合日本新標準!
可輕易的安裝。
HONDA/KAWASAKI/SUZUKI 正牙螺絲後照鏡車型無需使用原廠轉接座。
透過簡單的後照鏡改裝,摩托車的外觀就會有明顯的改變。
具備了大鏡面,可以方便的顯示後方狀況,為騎士提供了安全保障。此外,鏡面部分還提供了調整器機構,可以將鏡面調整到喜歡的位置。
具有實用性和個性化的後照鏡。
【調整方式】
可以使用6mm六角扳手鬆開來調節角度。
角度可以每次進行18°的增量調整,鎖緊時請對準槽口。
如果沒有對準而鎖緊可能會壓傷槽口。(查看圖片)
日本後視鏡的安全標準已經修訂,日本新標準適用於在2005年1月之後獲得型式認可的新車型以及在2007年1月之後發布的繼續生產之車輛。
【新標準】
圓形類型的直徑為94mm以上且小於150mm。對於正方形等非圓形類型,應適合使用直徑為78mm的圓形,長度應為120mm,寬度應為200mm以下。
當後視鏡與行人擦撞時,可減輕撞擊的結構。
反射面的中心穿過活動裝置的中心,平行於行進方向的垂直平面外必須至少280 mm。
[注意]
※圖像包括其他顏色。
※請注意安裝方法。
※除了適用車型中列出的車型以外,未列出的車型尚未經確認或可能無法安裝。
※購買前請務必確認車子是否可以安裝。
※左右後視鏡都是正牙螺絲的車型可以直接安裝。(HONDA,KAWASAKI,SUZUKI)
※左側或右側後視鏡使用逆牙螺絲的車型,務必透過原廠的轉接座安裝。(YAMAHA)
※產品的顏色可能會因拍攝條件、螢幕、產品批次而異。
※產品規格可能會因製造商的情況不同而改變。請注意。
【要點】
※進口後視鏡,部分商品可能是以""單支""包裝販售,購買前請確認商品內容敘述,或透過"商品諮詢"進行確認
[Size] 80mm (length) x 140mm (width)
[Adjuster mechanism] 10-way (18 degree intervals)
[Set components]
・Main body (set of 2)
・10mm right handed screw x 2 / left handed screw x 1
・8mm right handed screw x 2 / left handed screw x 1
[Installation time] 0.2h
【商品描述】
[Size] 80mm (length) x 140mm (width)
[Adjuster mechanism] 10-way (18 degree intervals)
[Set components]
・Main body (set of 2)
・10mm right handed screw x 2 / left handed screw x 1
・8mm right handed screw x 2 / left handed screw x 1
[Installation time] 0.2h
【注意】
*Image may contain other colors.
*Please note the installation instructions.
*The installation of models is not checked other than those listed in the compatibility check list.If your vehicle is not listed, it cannot be installed or has not been tested.
*Please make sure to check the vehicle before placing an order.
*This product can be installed as it is if the mirror mounting part is right handed screw on both sides.(HONDA, KAWASAKI, SUZUKI)
*For vehicles with mirror mountings that are left handed screw on either side, be sure to use the stock adapter.(Yamaha)
*The color of the product may vary depending on the shooting conditions, monitor, product lot, and left and right of the set product.
*[How to adjust]
The angle can be adjusted by loosening with a 6mm hex wrench.
The angle can be adjusted in 18° increments.When tightening, align with the groove, otherwise the groove may be crushed.(See image)
*[New standard]
For a circular type, the diameter must be between 94mm and 150mm, and for a non-circular type such as a square type, the diameter must be 78mm and the length must be 120mm and the width must be 200mm or less.
Its structure soften the impact when the mirror comes into contact with a pedestrian.
The center of the reflective surface shall be at least 280 mm outside the vertical plane parallel to the direction of travel, passing through the center of the steering device.
*There may be changes in product specifications due to the manufacturer's reasons.