PAGE TOP

GH07 Grip Heater with Output System on Left Side, Grip Length 115mm

  • Brand: KIJIMA
  • Product ID: 304-8197

List price: TWD 5,630

Selling price: TWD 3,752 33%OFF

Spring Sale: Free Shipping Event from Now Until March 31!
Enjoy Free Shipping on Orders Over TWD 9,999!
※EMS shipping only.

Get 38 Webike point (Around NT$ 38 )
*Can be used as a discount on your next purchase.

Pre-sale Service

TWD 3752.000000

38 Webike point

Once you select the option, estimate delivery time will be displayed.

QTY:
Webike STOCK RECOMMENDATIONS - FAST SHIP
【SUZUKI】Grip Heater 廠商在庫
SUZUKI

Grip Heater

$5,691(68%)

【KIJIMA】Grip Heater GH08 Push Switch Inch 廠商在庫
【KIJIMA】Grip Heater GH07 Switch Built-in 廠商在庫
【KIJIMA】Grip Heater GH07 with Built-In Switch Inch 廠商在庫
【KIJIMA】5-stage handle push-switch grip heater GH08 廠商在庫
【YAMAHA】Grip Warmer MT09TRA 廠商在庫
YAMAHA

Grip Warmer MT09TRA

$7,309(71%)

【HONDA】Grip Heater 廠商在庫
HONDA

Grip Heater

$2,594(65%)

【YAMAHA】Grip Warmer 廠商在庫
YAMAHA

Grip Warmer

$8,600(74%)

【HONDA】Sports Grip Heater 廠商在庫
HONDA

Sports Grip Heater

$2,932(65%)

【HONDA】Sports Grip Heater 廠商在庫
HONDA

Sports Grip Heater

$3,758(67%)

【DAYTONA】Hot Grip Wrapping Type EASY2 廠商在庫
DAYTONA

Hot Grip Wrapping Type EASY2

$1,758(64%)

【SUZUKI】Grip Heater 廠商在庫
SUZUKI

Grip Heater

$6,780(71%)

【SP武川】Heat Grip TYPE-ROLL 廠商在庫
SP武川

Heat Grip TYPE-ROLL

$1,423(60%)

FITMENT

【要點】

Grip length: 115mm
For standard handlebar: 22.2mm
Power consumption: 8W-36W
Switch built-in type

[Set components]
・Left / Right grips (left: Built-in switch)
・Mounting wiring
・End caps, etc.

【商品描述】

Grip length: 115mm
For standard handlebar: 22.2mm
Power consumption: 8W-36W
Switch built-in type

[Set components]
・Left / Right grips (left: Built-in switch)
・Mounting wiring
・End caps, etc.

【注意】

*The stock optional grip heaters manufactured by Honda have a half-wound heating wire, but this product has a full-wound heating wire.The power consumption is higher than that of Honda's optional grip heaters, and starting and using the grip heaters at max heat immediately after engine startup will significantly drain the life of the on-board battery.The life of the battery and electrical system will be extended if the bike is sufficiently ready for startup after the engine has been started, idled, and run 2-3 km.
*Since motorcycles are not power generators, do not use them recklessly. Instead, use the surplus electrical power of the motorcycle gradually. This approach is gentle on the motorcycle.Also, please consider the use of a handlebar cover to increase the overall effect of thermal protection and warmth under low power use.Since the wind blows on your hands and they get cold, if you can physically block the wind, your hands will be less likely to get cold and heat will accumulate.
*With the recent trend toward expansion of electrical components, we have heard from many customers that only the grip heater option is not enough.Motorcycles move by burning fuel, and their explosive power is also used to generate electricity, powering various electrical equipment. Therefore, when considering installation, it is important to first discuss with your bike shop about the essential and preferable options for your bike's electrical accessories. We kindly ask for your careful consideration after consulting with the shop before proceeding with the installation.
*The power demand is so high that even if the system can be used at level 5 of the 5 maximum heat levels when riding on highways or expressways, the battery protection function may automatically stop the power supply when the bike is stopped in traffic jams or at traffic lights.In such a case, please make sure to start up and use it again after reaching cruising speed.
*When installing on a stock or aftermarket throttle tube, it is recommended to warm up the throttle tube before installation to allow for thermal expansion and easier installation.
*For some bikes, the stock-installed scanning system may initialize the memory function of the grip heater without the knowledge of the owner or dealer.Since it is not possible to cut off the scanning system installed on the bike, please consider adding a switch wire to manage the system.No additional wiring is required if you are not particularly dissatisfied with starting up and using the system from the first initialization stage each time.
*Full cowl bikes and scooters may require more labor and may require a longer period of time since the wiring cowl will be threaded during installation.Also, since it is an electrical component, the location for supplying electricity may vary depending on the bike for the optional coupler or surplus wiring. Even if the grip length that can be installed is long, if the wiring work for supplying power is technically difficult and cannot be installed during storage, it could be a problem.Before proceeding, please consult with the bike shop in advance and consider it.
Regarding the corresponding throttle pipe, please thoroughly check the condition of the stock parts and the stock part number. Also, carefully consider that depending on the length of the grip heater, it may not be possible to use stock bar ends.
*In recent times, there has been remarkable progress in motorcycle equipment, and many bikes are now equipped with high-quality components such as heated grips as standard features upon delivery.In this case, please confirm not only this compatibility data but also the actual condition of the bike with the bike dealer.
*If this product is installed on a vehicle with a low battery capacity or power generation, it will not only fail to warm up, but will also cause the battery to run out of power, which is often happen to the vehicle with 125cc or less.Please check the current condition of your vehicle, and check if the voltage is more than the specified 13.4V with the engine running, and also check if there is any effect on other electrical components, such as dimming of the lights, including the use of other electrical components.Depending on the condition of the vehicle, it may not be able to demonstrate sufficient performance.
*Images may contain other products.
*There may be changes in product specifications due to the manufacturer's reasons.

QA(1)

1.我車GSX1400.請教我應該選 1300?還是選1300(1吋把手用)

"1吋"為英制把手規格,多為美式機車使用,因此請先確認您把手直徑,再來選購您需要的握把寬度。

REVIEWS FOR THIS PRODUCT(0)

0/5